The Noble Radio NR-4SC is a simple to use 10 Watt (minimum) 4 Meter SSB/CW transceiver.
The radio operates USB and CW.
The Noble Radio NR-4SC uses a single conversion design with an IF
frequency of 10.7 MHz. Front end
bandpass filters limit out of band signals into the RF Preamp stage.
A double balanced diode ring mixer provides good strong signal handling
capability. There are two 8 pole crystal
filters following the mixer which are designed for 3.0 kHz and 500 Hz -6dB
bandwidths. The 3 kHz filter allows for good SSB voice fidelity while the 500
Hz filter provides good adjacent channel rejection on CW. Either filter can be
selected in both modes.
Specifications*
1) SSB/CW
2) 10 Watt output power
3) Built in Iambic keyer
4) Analog S-meter, not a bargraph.
5) RIT
6) SPLIT
7) Variable Speed Tuning VST
8) Wide and Narrow filter
9) Fast and Slow selectable AGC
10) Output to key an external Amplifier
11) Can be switched for QSK and Non QSK compatible Amps
12) Simultaneous display of RX and TX frequencies
13) 13.8VDC at 4 Amps TX current
14) 650 mA RX current
15) Built in loudspeaker
16) Audio output .6 Watt
17) 10.7 MHz IF output
18) RX Sensitivity -130dbm MDS
19) IF rejection greater than 100db
20) Blocking dynamic range 107db
21) Third Order Dynamic Range = 96db (IP3 = +14dBm)
22) 2nd Order Dynamic Range 87db (IP2 = +44dBm)
23) TX spurious is better than – 55dBc which meets CE ETSI EN301 783-1 standards
1) SSB/CW
2) 10 Watt output power
3) Built in Iambic keyer
4) Analog S-meter, not a bargraph.
5) RIT
6) SPLIT
7) Variable Speed Tuning VST
8) Wide and Narrow filter
9) Fast and Slow selectable AGC
10) Output to key an external Amplifier
11) Can be switched for QSK and Non QSK compatible Amps
12) Simultaneous display of RX and TX frequencies
13) 13.8VDC at 4 Amps TX current
14) 650 mA RX current
15) Built in loudspeaker
16) Audio output .6 Watt
17) 10.7 MHz IF output
18) RX Sensitivity -130dbm MDS
19) IF rejection greater than 100db
20) Blocking dynamic range 107db
21) Third Order Dynamic Range = 96db (IP3 = +14dBm)
22) 2nd Order Dynamic Range 87db (IP2 = +44dBm)
23) TX spurious is better than – 55dBc which meets CE ETSI EN301 783-1 standards
* All specifications in this document may be subject to change without
notice or obligation
Noble Radio
Two IF amplifier stages and fast attack AGC provide good re-ceiver
sensitivity while leveling the audio output on strong sig-nals. AGC action starts at approximately a -120 dBm input
signal level.
The local oscillator is derived from a DDS/PLL circuit pro-viding a high
degree of stability and low noise.
A high stability 107.374 MHz reference oscillator is used for all local
oscillator generation. The high
frequency provides low DDS spurious out-put.
The transceiver offers a 10.7MHz IF out on the back panel for connection
to an SDR so it may be used with a PC for a Spec-tral Display.
Other features of the NR-4SC include RIT (Receiver Incremental Tuning)
and SPLIT mode
functions as well as a built in Iambic Keyer for CW.
The AGC rate has a FAST and SLOW speed to suit operator preference.
See More: http://www.nobleradio.eu/
Source: http://qrznow.com/noble-radio
73
